拒绝树莓派断电无法启动

2020-03-08  本文已影响0人  XS小四

创建影子系统

修改root用户

# 修改为 root 用户，输入2次密码即可，之后重新登录
sudo passwd root
# 如果要使用 ssh 远程登录 root 还得修改 ssh 配置文件，追加一条：PermitRootLogin yes。默认是禁用的
vi /etc/ssh/sshd_config
1.更新系统及安装自己需要的软件
apt update
apt upgrade -y
2.禁用交换空间
dphys-swapfile swapoff
dphys-swapfile uninstall
update-rc.d dphys-swapfile remove
3.创建并拷贝overlayRoot.sh脚本

临时找个目录生成空的 overlayRoot.sh 文件

# 生成 overlayRoot.sh 文件
touch overlayRoot.sh
# 编辑 overlayRoot.sh 文件
vi overlayRoot.sh

以上生成文件成功之后，拷贝以下内容至overlayRoot.sh文件中

#!/bin/sh
# Read-only Root-FS for Raspian using overlayfs
# Version 1.0
#
# Created 2017 by Pascal Suter @ DALCO AG, Switzerland
# to work on Raspian as custom init script
# (raspbian does not use an initramfs on boot)
#
# Modified 2017-Apr-21 by Tony McBeardsley 
#
# This program is free software: you can redistribute it and/or modify
# it under the terms of the GNU General Public License as published by
# the Free Software Foundation, either version 3 of the License, or
# (at your option) any later version.
#
# This program is distributed in the hope that it will be useful,
# but WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
# GNU General Public License for more details.
#
# You should have received a copy of the GNU General Public License
# along with this program. If not, see
# <http://www.gnu.org/licenses/>.
#
#
# Tested with Raspbian mini, 2017-01-11
#
# This script will mount the root filesystem read-only and overlay it with a temporary tempfs 
# which is read-write mounted. This is done using the overlayFS which is part of the linux kernel 
# since version 3.18. 
# when this script is in use, all changes made to anywhere in the root filesystem mount will be lost 
# upon reboot of the system. The SD card will only be accessed as read-only drive, which significantly
# helps to prolong its life and prevent filesystem coruption in environments where the system is usually
# not shut down properly 
#
# Install: 
# copy this script to /sbin/overlayRoot.sh and add "init=/sbin/overlayRoot.sh" to the cmdline.txt 
# file in the raspbian image's boot partition. 
# I strongly recommend to disable swapping before using this. it will work with swap but that just does 
# not make sens as the swap file will be stored in the tempfs which again resides in the ram.
# run these commands on the booted raspberry pi BEFORE you set the init=/sbin/overlayRoot.sh boot option:
# sudo dphys-swapfile swapoff
# sudo dphys-swapfile uninstall
# sudo update-rc.d dphys-swapfile remove
#
# To install software, run upgrades and do other changes to the raspberry setup, simply remove the init= 
# entry from the cmdline.txt file and reboot, make the changes, add the init= entry and reboot once more. 

fail(){
 echo -e "$1"
 /bin/bash
}


# Load overlay module
modprobe overlay
if [ $? -ne 0 ]; then
    fail "ERROR: missing overlay kernel module"
fi


# Mount /proc
mount -t proc proc /proc
if [ $? -ne 0 ]; then
    fail "ERROR: could not mount proc"
fi


# Create a writable fs on /mnt to then create our mountpoints 
mount -t tmpfs inittemp /mnt
if [ $? -ne 0 ]; then
    fail "ERROR: could not create a temporary filesystem to mount the base filesystems for overlayfs"
fi


# Mount a tmpfs under /mnt/rw
mkdir /mnt/rw
mount -t tmpfs root-rw /mnt/rw
if [ $? -ne 0 ]; then
    fail "ERROR: could not create tempfs for upper filesystem"
fi



# Identify root fs device, PARTUUID, mount options and fs type

#rootDev=`blkid -o list | awk '$3 == "/" {print $1}'`
# Changed here(point to / ) in case the cmd above doesn't work # By ChenYang 20171122
rootDev=/dev/mmcblk0p2
rootPARTUUID=`awk '$2 == "/" {print $1}' /etc/fstab`
rootMountOpt=`awk '$2 == "/" {print $4}' /etc/fstab`
rootFsType=`awk '$2 == "/" {print $3}' /etc/fstab`


# Mount original root filesystem readonly under /mnt/lower
mkdir /mnt/lower
mount -t ${rootFsType} -o ${rootMountOpt},ro ${rootDev} /mnt/lower
if [ $? -ne 0 ]; then
    fail "ERROR: could not ro-mount original root partition"
fi


# Mount the overlay filesystem
mkdir /mnt/rw/upper
mkdir /mnt/rw/work
mkdir /mnt/newroot
mount -t overlay -o lowerdir=/mnt/lower,upperdir=/mnt/rw/upper,workdir=/mnt/rw/work overlayfs-root /mnt/newroot
if [ $? -ne 0 ]; then
    fail "ERROR: could not mount overlayFS"
fi


# Create mountpoints inside the new root filesystem-overlay
mkdir /mnt/newroot/ro
mkdir /mnt/newroot/rw

# Remove root mount from fstab (this is already a non-permanent modification)
grep -v "$rootPARTUUID" /mnt/lower/etc/fstab > /mnt/newroot/etc/fstab
echo "#the original root mount has been removed by overlayRoot.sh" >> /mnt/newroot/etc/fstab
echo "#this is only a temporary modification, the original fstab" >> /mnt/newroot/etc/fstab
echo "#stored on the disk can be found in /ro/etc/fstab" >> /mnt/newroot/etc/fstab


# Change to the new overlay root
cd /mnt/newroot
pivot_root . mnt
exec chroot . sh -c "$(cat <<END

 # Move ro and rw mounts to the new root
 mount --move /mnt/mnt/lower/ /ro
 if [ $? -ne 0 ]; then
     echo "ERROR: could not move ro-root into newroot"
     /bin/bash
 fi
 mount --move /mnt/mnt/rw /rw
 if [ $? -ne 0 ]; then
     echo "ERROR: could not move tempfs rw mount into newroot"
     /bin/bash
 fi

 # Unmount unneeded mounts so we can unmout the old readonly root
 umount /mnt/mnt
 umount /mnt/proc
 umount /mnt/dev
 umount /mnt

 # Continue with regular init
 exec /sbin/init
END
)"

拷贝生成的脚本至 /sbin 目录，并授权

# 拷贝脚本至 /sbin
cp overlayRoot.sh /sbin/overlayRoot.sh
# 授权脚本
chmod a+x /sbin/overlayRoot.sh
4.修改 cmdline.txt 文件

注意，修改该文件后，不要重启。重启后，即为影子系统了。任何新生文件或安装应用重启后均消失

# 打开 cmdline.txt
vi /boot/cmdline.txt

文件末尾追加以下内容： init=/sbin/overlayRoot.sh

追加前

➜ ~ cat /boot/cmdline.txt
console=serial0,115200 console=tty1 root=PARTUUID=ea7d04d6-02 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait quiet splash plymouth.ignore-serial-consoles
➜ ~

追加后

➜ ~ cat /boot/cmdline.txt
console=serial0,115200 console=tty1 root=PARTUUID=ea7d04d6-02 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait quiet splash plymouth.ignore-serial-consoles init=/sbin/overlayRoot.sh
➜ ~
5.修改boot分区为只读

为了保证整个 SD 卡都为只读，必须要单独修改 boot 分区为只读。否则默认 boot 分区仍然不是只读，依然可以写文件，重启后不会丢失，如此一来有风险造成意外断电 boot 分区文件丢失，导致无法启动。

# 打开 fstab，修改 boot 为只读
vi /etc/fstab

修改前

➜ ~ cat /etc/fstab       
proc /proc proc defaults 0 0
PARTUUID=ea7d04d6-01 /boot vfat defaults 0 2
PARTUUID=ea7d04d6-02 / ext4 defaults,noatime 0 1
# a swapfile is not a swap partition, no line here
# use dphys-swapfile swap[on|off] for that
➜ ~

修改后

➜ ~ cat /etc/fstab
proc /proc proc defaults 0 0
PARTUUID=ea7d04d6-01 /boot vfat defaults,ro 0 2
PARTUUID=ea7d04d6-02 / ext4 defaults,noatime 0 1
# a swapfile is not a swap partition, no line here
# use dphys-swapfile swap[on|off] for that
➜ ~

以上操作后，可以通过 mount 命令来查看各分区的读写状态，以便观察相关分区都为只读。

撤消影子系统（更新系统或重新安装软件时需要）

1.remount boot 分区为可写
mount -o remount,rw /boot
2.删除 cmdline.txt init 属性
vi /boot/cmdline.txt

删除前

➜ ~ cat /boot/cmdline.txt
console=serial0,115200 console=tty1 root=PARTUUID=ea7d04d6-02 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait quiet splash plymouth.ignore-serial-consoles init=/sbin/overlayRoot.sh
➜ ~

删除后

➜ ~ cat /boot/cmdline.txt
console=serial0,115200 console=tty1 root=PARTUUID=ea7d04d6-02 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait quiet splash plymouth.ignore-serial-consoles
➜ ~

以上修改后，重启即可生效

3.如果想修改 boot 分区内容，请修改 /etc/fstab 文件
# 打开 fstab
vi /etc/fstab

修改前

➜ ~ cat /etc/fstab
proc /proc proc defaults 0 0
PARTUUID=ea7d04d6-01 /boot vfat defaults,ro 0 2
PARTUUID=ea7d04d6-02 / ext4 defaults,noatime 0 1
# a swapfile is not a swap partition, no line here
# use dphys-swapfile swap[on|off] for that
➜ ~

修改后

➜ ~ cat /etc/fstab       
proc /proc proc defaults 0 0
PARTUUID=ea7d04d6-01 /boot vfat defaults 0 2
PARTUUID=ea7d04d6-02 / ext4 defaults,noatime 0 1
# a swapfile is not a swap partition, no line here
# use dphys-swapfile swap[on|off] for that
➜ ~
上一篇 下一篇

猜你喜欢

热点阅读